DIY Cement Planter Pot

I have a quick DIY on how to make your own planter pot with cement. Its absolutely easy to make and you can personalize in any way you want.

Materials required:

• Cement
• Any oil
• Painter’s tape
• Mold –Round plastic container in two sizes – I used a kitchen measuring cup and a yogurt container
• Silicone bumpers
• Water
• Mixing container
• Mixing stick
• Water based clear Sealer – polyacrylic
• Sand paper or Sanding block
• Acrylic paints

DISCLOSURE: We only recommend products we would use ourselves and all opinions are our own. This post may contain some affiliate links. If you click through and make a purchase, we earn few pennies at no additional cost to you. It helps us to keep ‘The nomad studio’ alive. Thanks for support!

DOs and DONTs

1. You can use any kind of mold for your casting. I have seen people use all kinds of material as mold. You can make silicone mold with this kit from amazon or buy one (like I did to make my DIY cement coaster) or make one with melamine wood or use any plastic container. It really depends on the size of your object and what shape you want to cast. If you are casting a small and simple object, you can also make a mold in the desired shape with cardboard. Once concrete cures, cardboard can be peeled off easily. 
2. Prepping the mold: Make sure the mold is water tight. If you are using any material other than silicone or melamine, I recommend coating the mold with clean vegetable oil or some release agent. This will help a lot when you demold.
3. Make sure that you follow the cement to water ratio as per the manufacturer’s specification. I have used ‘Cement All’ in this project. As per the direction, I used a 1:4 ratio. You want the mixture to be in pancake batter-like consistency.
4. After you fill the mold, it is very important to release the air bubbles. So, give a few taps on all sides and corners of the mold. If you are casting a bigger item, pound on the mold with a rubber mallet.
5. To add a personal touch, you can add liquid cement color to your concrete mix. In this project, I have only used acrylic paints to color the cement. In the case of acrylic paints, use as little as possible. Otherwise, it could affect the composition of the mixture.
6. After curing, you should seal it with a water-based sealer. I use this polyacrylic sealer for most of my projects. It gives a little shiny finish to it.

DIY Cement Planter Pot

Step – 1: Grease the inner sides of the big container and the outer of the small container with vegetable oil. You can use any kind of oil here. The oil will not mix with cement and it will make the demolding process easier.

• 

• 

Step – 2: Mix the cement. Follow the ratio as per the instructions given in the package. I use the ratio 1 : 4 water to cement ratio for the product ‘cement all’.

Step – 3: Pour the cement mix into the bigger container to fill only half. Then, tap on all sides. This will help to release the air pockets.

Step – 4: Insert the small container and push through the cement. The mixture will rise up on the sides. Now add weights in to the small container to hold its position. You can also tape the containers together to secure.

Step – 5: Tap on all sides again to release air bubbles. Let it cure for at least 24 hours.

Step – 6: Before de molding, try to loosen up the edges by scoring with a knife. Then, tap the exterior with rubber mallet to loosen up. Since we already oiled the mold, it can easily demold.

Step – 7 : Sand the whole piece and remove dust with clean towel.

Step – 8: Personalize the stand with any color paint you want or leave it as it is in cement color. Finally finish with water based clear sealer.

Step – 9: Add bumpers.

and here you go!

I have only added fake plants in here. If you want to keep real ones, you just need to drill a small drain hole at the bottom and place a catch plate under the pot.

Sharing is Caring! 🙂 on Twitter on Facebook on LinkedIn